This graduation work is a result of implementing Lean Production using OEE and SMED at Enics Sweden AB in Malmö. Enics doesn?t have an established improvement concept and therefore should this work serve as an introduction to possibly start with Lean Production. A result in this report is that an OEE value has been identified within a common order at Enics. Other results are that an implementation of a Lean-board has been implemented and furthermore, within SMED, a flag that indicates changeover..

The aim of this thesis is benchmarking of the program, based on dynamic programming, that earlier was written to imitate the production planning at TSS.This thesis starts with a chapter about the construction of the DP-program, a shorter description of one and each of the program parts and also a list over the in- and output data in each program part. The DP-program consists of six linked MATLAB-files that together produce an optimized production plan for the different planning groups at TSS. The program reads in and reformat the given data and optimize the production of the articles in one group. Finally it compounds all article production plans and give us a production alternative.After running the program with new data the result shows, resembling with previous results, that TSS could be able to make some distinct cost-savings. According to the program, a 50 % decrease of TSS production costs is possible. .

During the last years commercial Wind Power Turbines (WPT) has become larger regardingto the generator sizes and hub heights. Available hub heights around 100 meters is nowcommon, which has led to profitability for WPT located in forests where there normally are tolow wind speeds. The current knowledgement regarding turbulence and the variation in thewind profile for the outcome of the power production for the WPT in forests is limited.In this Master of Science thesis an investigation concerning forest located wind power plantshas been made. The purpose has been to investigate if plants located in forest perform lesscompared to wind power turbines located at more common locations.The analyses are based on statically material for determining the availability,production/generator size, production/hub height, production/swept area and how thetopography affect the Production results.The analyses show that the variation in Production result for WPT located in forest comparedto turbines located at other locations is small. The availability is high and the productionresults are good..

The report is about efficiency of a current production group where there is no clear production flow and there are some buffers between the operations. The efficiency is done with the help of a tool that is calledWork process of flow production which is used by Atlas Copco CTO. The most obviously results are that the lead time drops from 25 hours to 425 minutes and that the balancing loss decreases from 85 % to 8 %. The report focus on decreasing transports, decreasing buffers, more reliability in lead time and quality. And a more stimulating labour content for the workers is another result..

The report is about efficiency of a current production group where there is no clear production flow and there are some buffers between the operations. The efficiency is done with the help of a tool that is calledWork process of flow production which is used by Atlas Copco CTO. The most obviously results are that the lead time drops from 25 hours to 425 minutes and that the balancing loss decreases from 85 % to 8 %. The report focus on decreasing transports, decreasing buffers, more reliability in lead time and quality. And a more stimulating labour content for the workers is another result..

The purpose of this study is to investigate how much of the estimated annual electric energy production from Swedish wind power that actually was produced, as well as the history of this agreement over time. The aim is to also examine if there are properties that have caused some group of wind power plants to produce more or less, compared to their estimated production. Operational data on wind turbines collected by the Swedish Energy Agency was analyzed. A survey was made among owners of wind power plants with a nominal power of at least 2 MW. Two different methods for normal year correction of production data were used and compared.

This literature study deals with the pig industry and how group size and available floor area affects the animal welfare and the Production results. It shows that both the pigs? welfare and Production result can be affected negatively if the environment seems stressful for the pigs, and if they are housed in a narrow area. If the pigs are being exposed to either physiological or psychological stress factors their immune system can be decreased and the growth can be impaired. Influence by the social status of the pigs is also reviewed.

The report is about efficiency of a current production group where there is no clear production flow and there are some buffers between the operations. The efficiency is done with the help of a tool that is calledWork process of flow production which is used by Atlas Copco CTO. The most obviously results are that the lead time drops from 25 hours to 425 minutes and that the balancing loss decreases from 85 % to 8 %. The report focus on decreasing transports, decreasing buffers, more reliability in lead time and quality. And a more stimulating labour content for the workers is another result..

This study is done together with Sydved AB in the summer of 2012. The purpose of the study is to analyse how different quantity of assortments influence the production for forwarders and harvesters with multiple tree handling aggregate in thinning, by different tree volumes. To make this analyse a time study was performed where three entrepreneurs work has been analysed. Beside the analyse, of different quantity of assortments, has also been analysed how the tree volume and a forest fuel assortment effect the production. The result of this study shows that the quantities of assortments have a significant meaning for the production. The biggest differences are most distinct between one and three assortments in the smaller tree volumes where production goes down if the quantity of assortments increase.

The avowed aim in this project was to see how the Swedish egg production is today. My first question was if the Swedish egg producers egg production turn a profit. I have done five after calculation at five different egg producers with different systems from case to case. The difference has been the living system, the fodder and the egg price. They made a report in Uppsala, Sweden (Hoffman & Andersson, 1996), where the look forward to a Swedish cage ban and made calculations after that coming ban. After that they lift the Swedish ban of cages and the egg producers could invest in new cages who called the decorated cage.

The report is about efficiency of a current production group where there is no clear production flow and there are some buffers between the operations. The efficiency is done with the help of a tool that is calledWork process of flow production which is used by Atlas Copco CTO. The most obviously results are that the lead time drops from 25 hours to 425 minutes and that the balancing loss decreases from 85 % to 8 %. The report focus on decreasing transports, decreasing buffers, more reliability in lead time and quality. And a more stimulating labour content for the workers is another result..

The company is currently in a stage of improvement and has therefore taken the help of students at School of Engineering, Jonkoping University. The current production is batch, production layout is fixed. A bottleneck is created after the first station which leads to large efficiency loss.  The meaning of this report was to provide a layout suggestion with balanced workstations to a new production line. The conditions were that the production line would be one-way, driven by customers order and meet a demand of 40 products per week.

Lean Production is used by many manufacturing companies. Companies in process industries do not use Lean Production to the same extent today. This is part of the report's issue to explore how Lean Production can be applied to a company in the process industries.The investigated company is a processing company that manufactures various types of foil. The company wishes to streamline its production and has therefore asked the authors to examine if Lean Production can offer the company improvements in their production. Lean Production value stream mapping tool has been selected to identify and analyze the current state of two of its products in production.

The purpose of this master thesis is to investigate how nearby forests affect the energy production in wind turbines. To reach the purpose a case study is performed on three wind turbines sited on a field in a north-south line at Andersfält in the municipality of Halmstad, Sweden. Approximately 100 meters south of the southern wind turbine a forest is situated. The case study is divided into three sub studies where the difference in energy production, the affect of the forest and a wind meteorology model, WAsP, is studied. The result show that the forest have a significant influence and that the WAsP-model gives an incorrect result of the energy production in wind turbines sited near a forest..

This study includes a life cycle assessment, LCA, on an ecological produced cotton shirt for the company Reflective Circle, which designs ethical and ecological clothes.Initially were cotton farming and textile production studied to gather basic knowledge about the processes. Since this shirt is being ecological produced in the whole production chain, we studied what an ecological production means, but also how a conventional production works. When this was done we could start to discuss the differences and similarities between the production of the shirt and general conventional production.When the LCA was first initiated, the main focus was on the green house gas emissions from the manure at the cultivation. Thereafter the process steps such as picking, ginning, carding, spinning, weaving and sewing were being studied. The picking is done by hand, but the rest of the processes are handed by machines which consumes energy.